"Nia,
We are a warranty center for Pentair.
Not sure where Pentair stands on Amazon...however if we…"
We Know Pools
Poolside Chat
MasterTemp 250 won't start
I have a brand new MasterTemp 250 connected to an Easy Touch automation system. When I turn the heater on via my iPhone, or the Easy Touch panel, the heater displays 128, then r13, then it goes dark. Nothing happens after that and there are no…Continue
Started by Nick in Heaters & Heat Pumps 11 hours ago.
Pentair IC40 warranty 1 Reply
I was interested in buying a Pentair ic40 salt cell via Amazon. Will Pentair still honor the 1 yr warranty if something were to go wrong with the cell beyond Amazon's 30day return policy? Or do I need to purchase the cell through an…Continue
Started by Nia Wedhas in Sanitizers / Chlorinators / Chlorine & Bromine Feeders. Last reply by James W. Henry CBPools.net 22 minutes ago.
Suntouch says solar is on while actuator valve is closed 1 Reply
Just started having issues getting solar actuator valve open even though suntouch says solar is on. Any ideas? I have tries changing water temp way below actual temp, solar sensor location temp. is 135 degrees. Pls help.
Started by Troy Lowe in Automation / Pool Control Systems. Last reply by James W. Henry CBPools.net 44 minutes ago.
Intelliflo V3050 not always kicking on 1 Reply
My pump does not kick on certain mornings. I have an upgrade easytouch board that uses the com port to communicate with the pump. I can hear the board click but the pump does not start. I have to throw the breaker off and back on for the pump…Continue
Started by Chuck Scheiwe in Pumps. Last reply by James W. Henry CBPools.net 49 minutes ago.
Kreepy Krauly Kruiser
I have a Pentair Kreepy Krauly Kruiser that's worked well until this year. About once a day, I find it lying on its side. I have replaced the Vacuum Seal and also the Foot Pad to no avail. Any suggestions?Continue
Started by Norm Lionberger in Automatic Pool Cleaners 22 hours ago.
Help Please: Compool CP3400 indoor unit communication problems with outdoor control panel 1 Reply
Hi All,Anyone have any ideas to try??? I know the unit is old, but figured I would try to see if there is a quick fix before spending big $$$ getting a replacement.I have a Compool CP3400 indoor unit which is connected to the outdoor PCLX3400…Continue
Started by Bob Winslow in Automation / Pool Control Systems. Last reply by Steve Bischoff 16 hours ago.
Lots of IC40 Issues Here! - Case # TS01012150 3 Replies
I have a new IC40. Got 6 years out of my old one (the one with more lights in the unit). Installed this a few months ago (swim season comes early in El Paso), and it has yet to make any Chlorine. So I call it in to Pentair, and Daryl, a…Continue
Started by Devin in Sanitizers / Chlorinators / Chlorine & Bromine Feeders. Last reply by James W. Henry CBPools.net 13 hours ago.
Pentair400 Shut off at 96 degrees
Hi folks, Hoping someone can help me here. I have searching the internet for a few weeks now hoping to find a solution, but I have nearly given up. I should say, I have found similar posts/replies, but none of these solutions apply. My MT400…Continue
Started by Allan K in Heaters & Heat Pumps yesterday.
ic 40 not working 3 Replies
I have a 7 month old ic 40 (pool is 7 months old as well) that is not working. The salt level lights flash back and forth green to red, red to green and the flow light stays red all the time. I've done everything I can find to do cleaned filters…Continue
Started by Dee White in Sanitizers / Chlorinators / Chlorine & Bromine Feeders. Last reply by James W. Henry CBPools.net 13 hours ago.
temp sensor locations 2 Replies
I only have a flex tubing between my pump and filter.Would installing the water temp sensor after my filter be the next best location.Also I would like to see the temp difference between suction and return after the solar.could I connect the return…Continue
Started by paul in Pool Design, Building & Renovation. Last reply by paul 23 hours ago.
Blog Posts
Patriotic Pool Parties
Posted by Lauren Bankes, Community Manager on June 14, 2013 at 6:00am
Father's Day Celebrations by the Pool
Posted by Lauren Bankes, Community Manager on June 11, 2013 at 8:30pm
Announcing the Winner of our ENERGY STAR® Certified IntelliFlo® Pump Giveaway!
Posted by Pentair on June 10, 2013 at 7:23am
IMPORTANT Message For ScreenLogic® Interface Pool Automation Users
Posted by Pentair on June 7, 2013 at 12:30pm
The Swimsuit Style Guide for Women
Posted by Matt Giovanisci on May 21, 2013 at 7:14am
Videos
-
-
-
fire on water
Added by Anthony Miranda
-
-
Sekerawalkthrough
Added by Anthony Miranda
-
A Poseidon Pools Spa
Added by Anthony Miranda
Happening Now! Members Making a Splash
James W. Henry CBPools.net replied to Troy Lowe's discussion 'Suntouch says solar is on while actuator valve is closed'"Troy,
You may have a bad actuator.....flip the toggle switch on the back of the actuator to see it…"
James W. Henry CBPools.net replied to Chuck Scheiwe's discussion 'Intelliflo V3050 not always kicking on'"Chuck,
Check the com wire for chew marks or damage....not sure what the part number is but you may…"
Ken Breit replied to Ken Breit's discussion 'ScreenLogic v5.2.713 Black Screen (iPad only)'"Yes - I updated the app to v5.3.200 several times (including uninstall, reboot and reinstall). I…"
Nick posted a discussionMasterTemp 250 won't start
I have a brand new MasterTemp 250 connected to an Easy Touch automation system. When I turn the…See More
Tony C. monogramcustompools.com replied to Jon Garber's discussion 'Build 5.2.713, posted 6/04/13 Feedback'"great job on 713! It was worth the wait. We've updated a bunch of our customers…"
James W. Henry CBPools.net replied to Dee White's discussion 'ic 40 not working'"Awesome....glad to help."
Having browser trouble?
If you're experiencing problems when viewing items in Internet Explorer, we recommend switching to another web browser such as Mozilla Firefox, Safari or Google Chrome.
Content
PROMOTIONS
Photos
Events
Recent Pentair Facebook Posts
© 2013 Created by Pentair.
