I ran into a strange thing using the ScreenLogic2 application on my Mac.I wanted to set a run once program to run my High Temp program for a couple of hours tomorrow morning. When I added a Run Once…Continue
Started this discussion. Last reply by Pentair Product Technician-Ben Apr 30.
Hi,I've had my IntelliTouch and ScreenLogic for a year now and I'm very happy with it.I do have one nagging desire, though. I want more control over my heating options.I have a single pool with a…Continue
Started this discussion. Last reply by Jeremy Bennett Apr 18.
Hi,Currently I have a VS3050 for my, approximately, 25,000 gallon pool. In addition I also have a booster pump for the pool sweep. Recently the booster pump as started to make a terrible whining…Continue
Hi, I'm in the middle of renovating my 15x30 (15-20,000 gallon) pool. I really like the idea of the iPhone app to control the pool so we're investing in the IntelliTouch and ScreenLogic. We have the…Continue
I ran into a strange thing using the ScreenLogic2 application on my Mac.I wanted to set a run once program to run my High Temp program for a couple of hours tomorrow morning. When I added a Run Once program, though, it did not give me an option to set an option to set both the start and end time. Instead it shows the start and end time in the program but I can only change the start time. The end time is always 12 hours later than the start.I'd like to be able to set a run once program to run at…See More
"Just a thought. There is a setting in the ScreenLogic configuration that probably has an equivalent in the panel interface that requires the pump to be off for valve changes. I have not tested this but I'll bet that if you set this option then…"
"By the way, I have considered just detaching the gas heater from IntelliTouch and setting it manually for 75. Functionally this solves my problem but then I need to go to it anytime I want to change anything. I prefer to have the remote access…"
Hi,I've had my IntelliTouch and ScreenLogic for a year now and I'm very happy with it.I do have one nagging desire, though. I want more control over my heating options.I have a single pool with a Pentair MaxTherm natural gas heater and solar. I run the solar as my primary heat source and use the gas heater to boost the temp when needed. My options for heating are, Solar Only, Heater Only, or Solar Preferred which uses solar as long as the solar is providing heat or switches to gas otherwise. In…See More
"to further corroborate the ease of screenlogic 2...I am a pennsylvania based pool builder and I am in San Diego for a few days for a pool builder conference.
I just took the train (I am actually on it now returning) to LA to install a screenlogic 2…"
"Thank you again. Really appreciate your assistance here. It would appear the person who has been helping me is working with assumptions based on ScreenLogic1. "
"It was an issue before ScreenLogic2 but now it is not.
I removed the port forwards I had put in place for the older version.
I use a MacBook Pro and the OS X version of ScreenLogic2."
"Jeremy,
Thank you for your response. The key bit of info here is you were able to connect your Protocol Adaptor with an RJ45 to the airport extreme router to access the internet AND it all works now. Did you have to configure any of the…"
"John,
A lot changed with screenLogic2. My current setup is a hard line from the IntelliTouch to the ScreenLogic protocol adaptor and then RJ45 to the airport extreme. If the protocol adaptor has an appropriate IP then it just works.
I believe SL2…"
"Jeremy,
Like you, I invested in the IntelliTouch and ScreenLogic and now am setting it up. Transmitter from pool is set up but I have an Apple Extreme router (wireless router) and am being told I can't simply plug the ScreenLogic adaptor…"
"Thank you, Dennis. I watched my pool sweep this morning as the VS3050 turned on and went over 3000 rpm (for priming) and despite the high pressure coming out the returns the sweep barely moved. This, I think, proves your point.
As to replacing the…"
Hi,Currently I have a VS3050 for my, approximately, 25,000 gallon pool. In addition I also have a booster pump for the pool sweep. Recently the booster pump as started to make a terrible whining noise that my pool tech says is due to bad bearings and that only solution is to replace the pump. I'm curious if I could, instead, just remove the booster from the system and use the VS3050 at a higher speed to drive the sweep. Would I need to install any additional valves or other equipment to make…See More
"Thanks, Ben.
For #3, specifically, he was concerned about being able to read the salt level and set the chlorination level for the AquaRite chlorinator. If the chlorinator is being managed by the Intellitouch I don't see a way to…"
Hi, I'm in the middle of renovating my 15x30 (15-20,000 gallon) pool. I really like the idea of the iPhone app to control the pool so we're investing in the IntelliTouch and ScreenLogic. We have the Intellitouch all set up with the Mobiletouch wireless control and we're slowly getting all the equipment online. The ScreenLogic is still in the box. Before we start deploying it I have a few questions:1. ScreenLogic offers a 'wireless kit' to avoid the need for the 4 conductor wire from the…See More
If you're experiencing problems when viewing items in Internet Explorer, we recommend switching to another web browser such as Mozilla Firefox, Safari or Google Chrome.
